King Kutter Lawn Mower Part No 999993 User Manual Page 1

PO Box 1200 305 Commerce Drive Winfield, Alabama 35594 FLEX HITCH ROTARY MOWER OPERATION AND PARTS Part No 999993 www.kingkutter.com

Figure E Figure F Figure G Figure H Figure I 10

CAUTION: DO NOT over fill gearbox. This could cause damage to oil seals and can cause per-manent damage to the gearbox. This issue will not be covered

12 SAFETY TRAINING  Safety is a primary concern in the design and manufacture of our product. Un-fortunately, our efforts to provide safe equipme

PREPARTION  Never operate the tractor and mower until you have read and completely under-stand this manual, the Tractor Operator’s Man

OPERATIONAL SAFETY  The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product de

OPERATIONAL SAFETY continued...  Never allow the cutting blade to contact such items. Cut material higher at first, allowing rotary mower to clea

16 OPERATIONAL SAFETY continued...  Pass rotary mower diagonally through sharp dips and avoid sharp drops to pre-vent “hanging up” tractor and rota

ATTACHING TO TRACTOR STEP 1 Attach to tractor's category 1 three point hitch as describ

ATTACHING TO TRACTOR continued... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is to

19 SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Clamp e

20 OPERATING INSTRUCTIONS This mower was designed to CUT PASTURE GRASS AND ROUGH AREAS UP TO 1" IN DIAMETER.. Use of your rotary mower to c

Note: For best results in heavier cutting conditions adjust the deck so the rear of the mower is approximately 2" higher than the front. This met

MAINTENANCE 1). Periodically check and maintain proper gear oil level. 2). Every 8 hours, wheel fork (s), wheel hub (s), PTO shaft universal joint

23 MAINTENANCE SAFETY  Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.  Follow good shop practices.

24 SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you

25 1 2

26 3 4

27 5 6 7

28 MODEL NO. DESCRIPTION SN# XXXXXXXXXX 8 9

29 NOTES:

TO THE PURCHASER This manual contains valuable information about your new King Kutter Mower. It has been carefully prepared to give you help

30 FLEX HITCH KUTTER

31 Ref. No. Part Name Part Number Rotary Mower Size 4 Ft. 5 Ft. 6 Ft. 5 Ft. Stainless 1 Tire & Rim /w Hub 403001 403001 403001 403001

32 SHEAR PIN PTO SHAFT Ref. No. Part Name 147029 147242 147234 1 Roll Pin Kit (2pk), (1) 8 x 55mm, (1) 8 x 60mm 500131 500131 500131 2 Male

33 SLIP CLUTCH PTO SHAFT Ref. No. Part Name 147134 1 Cross Kit 170020 2 Roll Pin 170120 3 Female Tube End Yoke 151070 4 Inner Tube 151092 5

34 SLIP CLUTCH ASSEMBLY Ref. No. Part Name 7” 8” 1 Clutch Spring with Compression Bolts (Pkg 8) 500140 500140 2 Flanged Yoke 196006 196011 3

35 PTO SHAFTS COVER REMOVAL (Pictures are on next page) BONDIOLI- (BYPY) 1). There are 3 white tabs around the cover as

BONDIOLI COVER REMOVAL EUROCARDAN SERIES 4 COVER REMOVAL

37 PTO SHAFTS COVER REMOVAL EUROCARDAN SERIES 5 1). There are 2 black tabs around the cover as shown in (B in F

40 HP GEARBOX 38

Ref. No. Part Name Gearbox 184000 Gearbox 184005 Gearbox 184010 1 Snap Ring 106138 106138 106138 2 Input Seal (NAK 35 x 54 x 10) 156010 156010

It is the purchaser and/or operator’s responsibility to….  Read and understand the information contained in this manual.  Operate, lubricate,

1. Limited Warranty. King Kutter, Inc. (“King Kutter”), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail pur-chaser (“Purchaser

5 CONTENTS ITEM PAGE Safety ... 6 Assembly Instructions ...

SAFETY READ AND FOLLOW THE INSTRUCTIONS IN THIS MANUAL AND ESPECIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS INJ

EQUIPMENT SAFETY GUIDELINES  Safety of the operator and by standards is one of the main concerns in designing and devel-oping a mower. However, e

FLEX HITCH ROTARY MOWER ASSEMBLY INSTRUCTIONS STEP 1 Place rotary mower on a flat, level surface. (See Figure A) STEP 2 Remove the wired on PTO sha

9 Figure A Figure B Figure C Figure D